Oct 11, 2022

Public workspaceSDS-PAGE V.2

DOI
dx.doi.org/10.17504/protocols.io.5jyl85o7dl2w/v2
  • 1University of Cambridge
  • Reclone.org (The Reagent Collaboration Network)
  • Open Bioeconomy Lab
Anna Bird
Icon indicating open access to content
QR code linking to this content
DOI: dx.doi.org/10.17504/protocols.io.5jyl85o7dl2w/v2
Protocol Citation: Anna Bird, Chiara Gandini 2022. SDS-PAGE. protocols.io https://dx.doi.org/10.17504/protocols.io.5jyl85o7dl2w/v2Version created by Anna Bird
License: This is an open access protocol distributed under the terms of the Creative Commons Attribution License,  which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited
Protocol status: Working
We use this protocol and it's working
Created: October 11, 2022
Last Modified: October 11, 2022
Protocol Integer ID: 71156
Abstract
SDS-PAGE gels are used to visualize proteins. This protocol describes how to prepare all the buffers required for casting and running SDS-PAGE gels, as well as how to prepare whole cell samples.
Protocol materials
ReagentTrisP212121
ReagentTrisP212121
ReagentTrisP212121
ReagentGlycine
ReagentSodium Dodecyl SulfateP212121
ReagentAmmonium persulfateCatalog #A3678
ReagentSodium Dodecyl SulfateP212121
Buffers
Buffers
10m
10m
4X Resolving Buffer (1.5 M Tris-HCl, pH 8.8)
  • Add 90.75 g ReagentTrisP212121 to Amount400 mL DI water
  • Titrate the solution with ~18% HCl to pH 8.8
  • Add water to a final volume of Amount500 mL
  • Store at 4°C



10m
4X Stacking Buffer (0.5 M Tris-HCl, pH 6.8)
  • Add 30.25 g ReagentTrisP212121 to Amount400 mL DI water
  • Titrate the solution with ~18% HCl to pH 6.8
  • Add water to a final volume of Amount500 mL DI water
  • Store at 4°C
10m
10X Running Buffer
  • Weigh 30 g TrisReagentTrisP212121 .
  • Weigh 144 g ReagentGlycine .
  • Weigh 10 g ReagentSodium Dodecyl SulfateP212121 SDS.
  • Dissolve in Amount1000 mL water.
  • pH should read 8.3. No pH adjustments are needed.
  • Dilute to 1X before use.
  • Store at room temperature.





15m
10% Ammonium Persulfate (w/v)
  • Add 1g of ReagentAmmonium persulfateCatalog #A3678 to Amount10 mL of DI water
  • Store at 4°C


5m
10% SDS (w/v)
  • Add 10g of ReagentSodium Dodecyl SulfateP212121 to Amount100 mL DI water
  • Store at room temperature


5m
3X Laemmli Buffer
  • 2.4 mL 1 M Tris pH 6.8
  • 3 mL 20% SDS
  • 3 mL glycerol
  • 1.6 mL beta mercaptoethanol
  • a drop of bromophoenol blue
10m
Gel Casting
Gel Casting
5m
5m
In an Eppendorf tube combine
  • Amount0.5 mL 30% Acrylamide: Bisacrylamide (29:1)
  • Amount0.5 mL DI water
  • Amount10 µL APS
  • Amount1 µL TEMED
Pipette Amount200 µL down the right side, and Amount200 µL down the left side
Allow to solidify for Duration00:05:00



5m
Resolving Layer

This following recipe makes a 12% SDS-PAGE. For optimal resolution of large proteins (25-200 kDa), you should use smaller concentration of acrylamide (8%), and for resolution of small proteins (4-70 kDa), you should use higher percentage of acrylamide (12-15%). You can calculate a recipe for a different gel percentage using https://www.cytographica.com/lab/acryl2.html
Combine
  • Amount1.645 mL DI water
  • Amount1.645 mL 30% Acrylamide: Bisacrylamide (29:1)
  • Amount1.25 mL 4X Resolving Buffer (1.5 M Tris, pH 8.8)
  • Amount50 µL 10% SDS
  • Amount50 µL 10% APS
  • Amount5 µL TEMED
TEMED must be used in a fume hood
Add APS just before casting as the gel begins to polymerize immediately after addition of APS.





  • Pour into the mold, leaving ~2 cm below where the bottom of the comb will be
  • Cover with a layer of isopropyl alcohol (IPA)
  • Wait Duration00:20:00 for gel to solidify

20m
Stacking Layer

The stacking layer helps all the proteins get lined up so all proteins enter the resolving layer at the same time
Dump out any excess IPA

Combine
  • Amount2.6 mL DI water
  • Amount1 mL 30% Acrylamide: Bisacrylamide (29:1)
  • Amount1.25 mL Stacking Buffer (0.5 M Tris, pH 6.8)
  • Amount50 µL 10% SDS
  • Amount50 µL 10% APS
  • Amount5 µL TEMED
TEMED must be used in the fume hood
Add APS just before casting as the gel begins to polymerize immediately after addition of APS.





10m
  • Pour into the mold
  • Place the comb
  • Wait Duration00:15:00 for gel to solidify
  • Move to water storage


15m
Sample Preparation
Sample Preparation
Preparation of Whole Cell Samples for SDS-PAGE analysis

Collect whole cell samples before and after induction, and normalize to the cell mass. This allows you to compare the protein expression before and after inducing cells.
  • Heat the waterbath or heatblock to Temperature95 °C
  • Read the optical density at 600 nm (OD600) of the cell culture using a photometer.

Note: the OD600 reading should be within the linear range of the photometer. If the reading appear to be lower than 0.1 or higher than 0.9 concentrate or dilute the cell sample accordingly in order to ensure the OD reading to fall within the 0.1- 0.9 range. If you dilute or concentrate the sample remember to calculate back the initial concentration (e.g. if you diluted 5 times the initial concentration is y*5, where y is the reading you have obtained from the diluted concentration)

5m
  • Calculate the amount of culture to harvest to have a cell pellet equivalent to 1mL of OD600 =1.

Calculate the amount of biomass using the formula
Ci * Vi = Cf * Vf
where C stands for "concentration", V stands for "volume", i stands for "initial" and f stands for "final". Therefore:
y OD600 * x mL = 1 OD600* 1 mL
where y is the OD600 reading and x is the volume to be calculated. Therefore
x mL = ( 1 * 1 )/y

  • Transfer the amount of culture as calculated into an appropriate tube and centrifuge it at 7,000 rpm for Duration00:10:00 in tabletop centrifuge
  • Discard the supernatant

10m

  • Transfer Amount150 µL of 1X Laemmli Sample Buffer in the tube and resuspend the pellet by pipetting.
  • Transfer the tube to the water bath/heatblock, inserting it into the floaters and incubate the tube at Temperature95 °C for Duration00:05:00
  • Transfer the tube on ice for Duration00:01:00
  • Transfer the tube in a bench-top centrifuge and centrifuge at room temperature at max speed (e.g. 13,000 xg) for Duration00:05:00
  • Transfer the supernatant to a final 1.5 microcentrifuge tube. Note: the pellet won't be visible. Remove the supernatant without touching the bottom of the tube with the pipette tips to avoid carry-over of membranes. This step is necessary to remove membranes and debris that will affect a good quality run of the samples on the SDS-PAGE gel.
  • Load Amount10 µL of the supernatant on the SDS-PAGE gel.
  • Store the remaining sample at Temperature-20 °C .

11m
Purified Protein
  • Add Amount2.5 µL of 3X Laemmli Buffer to Amount7.5 µL of sample
  • Incubate Duration00:05:00 at Temperature95 °C .
  • Load the sample onto the SDS-PAGE gel.
5m
Running the Gel
Running the Gel
1h 30m
1h 30m
  • Place in gel running box and cover with running buffer
  • If running only one gel, make sure the other side has a dummy gel cassette inserted.
  • Fill the space between the two gels with 1X running buffer.
  • Add Amount7.5 µL ladder with dye to a well. Add 7.5 - 10 uL samples to wells.
  • Run at 80V until the loading dye reaches the resolving/stacking layer interface.
  • Run at 180V until the loading dye reaches the end of the gel.
  • Remove gel from casing. Place in petri dish and cover with Coomassie blue dye. Allow to stain overnight.

1h 30m